Rancang Bangun Panel Instalasi Listrik Berbasis Engineering safety untuk Oven Pengecatan Bodi Kendaraan
DOI:
https://doi.org/10.24036/jtpvi.v3i4.376Keywords:
Engineering safety , panel instalasi listrik, oven pengecatan, keselamatan kerja, Miniature Circuit Breaker (MCB), Emergency Stop, pendidikan vokasi otomotifAbstract
Keselamatan kerja pada ruang oven pengecatan bodi kendaraan sering terabaikan, terutama pada sistem kelistrikan yang beroperasi pada suhu tinggi dan kelembapan tinggi. Penelitian ini bertujuan merancang dan membangun panel instalasi listrik berbasis engineering safety untuk oven pengecatan di Laboratorium Teknik Otomotif Universitas Negeri Padang. Penelitian menggunakan metode Research and Development dengan model Planning, Production, and Evaluation (PPE). Panel dirancang untuk melayani beban 3.736,6 W pada tegangan 220 V, dilengkapi Miniature Circuit Breaker (MCB) 20 A, tombol Emergency Stop, sistem grounding, pilot lamp, dan thermostat yang mengacu pada standar SNI dan PUIL 2011. Validasi dua ahli menyatakan panel layak digunakan, sedangkan uji fungsional menunjukkan MCB bekerja responsif dan tombol Emergency Stop mampu memutus arus dalam waktu kurang dari 0,5 detik. Hasil ini mengindikasikan bahwa panel yang dikembangkan efektif meningkatkan keselamatan kerja dan menjadi media pembelajaran praktikum kelistrikan serta teknologi pengecatan di pendidikan vokasi otomotif.
Occupational safety in painting ovens is often overlooked, particularly in electrical systems operating in high-temperature, high-humidity environments. This study designs and constructs an electrical installation panel based on engineering safety principles in the Automotive Engineering Laboratory of Universitas Negeri Padang using a Research and Development approach with the Planning, Production, and Evaluation (PPE) model. The panel supplies a load of 3,736.6 W at 220 V and is equipped with a 20 A Miniature Circuit Breaker (MCB), Emergency Stop button, grounding system, pilot lamp, and thermostat in accordance with SNI and PUIL 2011. Validation by two experts confirmed that the panel is feasible for use, while functional testing showed that the MCB operates responsively and the Emergency Stop disconnects the circuit in less than 0.5 s. These findings indicate that the panel enhances safety and provides a practical learning medium for electrical systems and painting technology in vocational automotive education.
References
[1] A. R. Laoli, M. S. D. Mendrofa, S. M. Kakisina, and K. S. Zai, “Analisis Quality Control dalam Meningkatkan Kualitas Hasil Body Paint di Abraham Motor,” J. Ekon. Bisnis, Manaj., dan Akunt., vol. 4, no. 3, pp. 1885–1894, 2024, doi: 10.35912/jebma.v4i3.254.
[2] A. Makkulau et al., “Edukasi Listrik Sehat untuk Mencegah Bahaya Kebakaran pada Perumahan Padat Penduduk di Jakarta Barat,” Minda Baharu, vol. 8, no. 1, pp. 189–200, 2024, doi: 10.33373/jmb.v8i1.5886. [Online]. Available: https://www.journal.unrika.ac.id/index.php/MNDBHRU.
[3] D. A. Pratiwi, A. I. Soumi, and W. Kurniawan, “The Effect of Light Type and Distance on Indoor Photovoltaic System,” JTERA (Jurnal Teknologi Rekayasa), vol. 8, no. 2, pp. 271–278, 2024, doi: 10.31544/jtera.v8.i2.2023.271-278.
[4] D. P. Nanggala and A. Ahfas, “Sub Distribution Panel’s Design Rancangan SubDistribution Panel,” Procedia Eng. Life Sci., vol. 5, pp. 355–361, 2024, doi: 10.21070/pels.v7i0.1484.
[5] ] M. H. Prasetya and A. S. Wardoyo, “Rancang Bangun Safety Device dan Rangkaian Kontrol untuk Mesin Pengupas Kabel,” J. Instrumentasi dan Teknologi Informasi, vol. 4, no. 1, pp. 8–16, 2022.
[6] S. Muhamad and H. Munnik, “Rancang Bangun Sistem Keamanan Rumah Menggunakan Relay,” J. Teknol. Elektro, Univ. Mercu Buana, vol. 8, no. 2, pp. 87–94, May 2017, doi: 10.22441/jte.v8i2.1601.
[7] N. Indrihastuti, A. Prayoga, and M. Musyaffa, “Perancangan Kendali 2 Kontaktor Bekerja Berurutan Secara Otomatis Berbasis PLC CPM1A 40CDR_A,” J. Cahaya Bagaskara, vol. 6, no. 2, pp. 15–22, Aug. 2021.
[8] D. R. H. Desrul, R. A. Priramadhi, and D. Darlis, “Sistem Keamanan Pada Alat Penyalur Daya Listrik Portable,” e-Proceeding Eng., vol. 11, no. 1, pp. 39–42, Feb. 2024.
[9] P. Yosua, D. B. Santoso, and A. Stefanie, “Rancang Bangun Automatic Washing and Drying System untuk Mesin Pencuci Cylinder Block Motor,” J. Ilm. Wahana Pendidik., vol. 7, no. 4, pp. 430–444, 2021, doi: 10.5281/zenodo.5167080.
[10] Y. M. Seftiani and Novizon, “Studi Kelayakan Sistem Pentanahan pada Gedung Teknik Elektro Universitas Andalas,” Elektron: J. Ilm., vol. 14, no. 2, pp. 45–49, Dec. 2022, doi: 10.30630/eji.14.2.297.
[11] H. D. R. K. T. Suryadi et al., “Teknologi Pengeringan dalam Proses Pengecatan,” Tek. Indones., 2018.
[12] Rahman et al., “Energy-Efficient Design of Paint Drying Ovens Using Thermal Insulation,” Mech. Eng. Res., vol. 12, no. 3, pp. 45–52, 2020.
[13] D. P. Sekulic, “Compact Heat Exchangers,” in Handbook of Thermal Science and Engineering. Cham, Switzerland: Springer, 2018, pp. 1501–1520, doi: 10.1007/978-3-319-26695-4_36.
[14] Krause, “Infrared Curing and Drying,” 2020.
[15] A. C. Irawan, A. Zulkarnain, and A. Sembiring, “Saklar Lampu Otomatis dengan Kendali Android Berbasis Mikrokontroller,” J. Ilmu Komput. dan Sist. Komput. Terap. (JIKSTRA), vol. 3, no. 2, pp. 59–67, Oct. 2021, doi: 10.35447/jikstra.v3i2.396.
[16] M. Zhang, H. Chen, A. S. Mujumdar, J. Tang, S. Miao, and Y. Wang, “Recent developments in high-quality drying of vegetables, fruits, and aquatic products,” Crit. Rev. Food Sci. Nutr., vol. 57, no. 6, pp. 1239–1255, 2017, doi: 10.1080/10408398.2014.979280.
[17] R. Singh, P. Kuchhal, S. Choudhury, and A. Gehlot, “Implementation and evaluation of heating system using PID with genetic algorithm,” Indian J. Sci. Technol., vol. 8, no. 5, pp. 413–418, 2015, doi: 10.17485/ijst/2015/v8i5/60472.
[18] Y. Yin, J. Yang, Y. Jia, S. Lan, and Z. Liao, “Modeling of Ventilation’s Influence on Energy Consumption in Multi-cylinder Dryer Section Part 2: Simulations and Applications,” Int. J. Comput. Intell. Syst., vol. 15, no. 1, Art. no. 40, 2022, doi: 10.1007/s44196-022-00095-4.
[19] F. D. U. Gayuh, “Pengaruh Kecepatan dan Arah Aliran Udara Terhadap Kondisi Udara Dalam Ruangan Pada Sistem Ventilasi Alamiah,” J. Rekayasa Mesin, vol. 3, no. 2, pp. 299–304, 2012.
[20] U. Nursusanto, S. Rahman, and A. Sony, “Edukasi Keselamatan Ketenagalistrikan Pada Instalasi Listrik Bangunan Residensial,” J. Tek. Elektro: Electron. Control, Telecommun., Comput. Inf. Power Syst., vol. 10, no. 1, pp. 79–90, Mar. 2025.
[21] A. G. Hutajulu, M. C. Malino, and J. M. Tambunan, “Implementasi Pengujian Karakteristik Miniatur Circuit Breaker Berdasarkan SNI 60898-1:2009 di PT PLN (Persero) Pusat Sertifikasi,” in Pros. Semin. Nas. Penelit. LPPM UMJ, Nov. 2024, pp. 1–10. [Online]. Available: http://jurnal.umj.ac.id/index.php/semnaslit.
[22] A. Syahid and D. Suhardi, “Analisa Desain Instalasi Listrik Gedung 11 Lantai Tower 3 Institut Teknologi Sepuluh Nopember Surabaya,” Semin. Keinsinyuran Progr. Stud. Progr. Profesi Ins., vol. 2, no. 1, pp. 18–27, 2021, doi: 10.22219/skpsppi.v2i1.4339.
[23] Sugiyono, Metode Penelitian Pendidikan: Pendekatan Kuantitatif, Kualitatif, dan R&D. Bandung, Indonesia: Alfabeta, 2019.
[24] Sugiyono, Metode Penelitian Pendidikan: Kuantitatif, Kualitatif dan Kombinasi. Bandung, Indonesia: Alfabeta, 2017.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Fawwaz Naufal, Ahmad Arif, Hasan Maksum, Donny Fernandez
This work is licensed under a Creative Commons Attribution 4.0 International License.
